When we talk about sterilization in the dental office, it is common to focus all the attention on the equipment: temperature, pressure, time, cycle.
These parameters are fundamental. But there is a difference between having an autoclave capable of carrying out a sterilization cycle and having a controlled and validated sterilization process.
The final result depends on a sequence of steps that begins before the instrument enters the chamber.
The CDC's own guidance highlights that the processing of instruments must follow a correct sequence — including cleaning, preparation, sterilization, monitoring and storage — and that failures at any stage can compromise the result (CDC, 2024).
Imagine an instrument that arrives in the autoclave with organic matter attached.
Steam needs to come into effective contact with surfaces that need to be sterilized.
If residues remain on the instrument, they can protect microorganisms and hinder the sterilization process (CDC, 2024).
Therefore, cleaning is not a secondary step.
She prepares the instruments so that sterilization can take place properly.
The autoclave sterilizes what has been correctly prepared to be sterilized.
It is important not to confuse:
Cleaning → removes organic matter and residues.
Disinfection → reduces or eliminates certain microorganisms, but not necessarily all microorganisms and spores.
Sterilization → seeks to eliminate all forms of microbial life, including bacterial spores.
This distinction is fundamental to understand why simply “passing the instrument in the autoclave” does not represent the entire reprocessing process (CDC, 2024).
In steam sterilization, the principle is relatively simple:
steam + temperature + pressure + time + adequate contact.
The steam needs to reach the instrument surfaces at the required temperature and for the required period.
Pressure, in this context, is used to allow the system to reach the temperatures necessary for sterilization.
The CDC describes steam, pressure, temperature, and time as fundamental parameters of steam sterilization (CDC, 2023).
This has an important consequence:
There is no “autoclave temperature” in isolation. There is a cycle with parameters that need to act together.
An autoclave can be working perfectly and still have a cycle that has problems if the load is prepared incorrectly.
Overloaded instruments, inadequate packaging or arrangements that prevent the circulation of the sterilizing agent can make it difficult for the steam to come into contact with all surfaces.
CDC recommendations advise that items be organized to allow free circulation of the sterilizing agent and that the manufacturer's instructions for loading the equipment be followed (CDC, 2003; CDC, 2024).
And this is interesting because it shows that:
the performance of the equipment also depends on the way it is used.
This is perhaps the most important point of the article.
The end of the cycle informs that the equipment has completed that programming. But the process needs to be monitored. The CDC recommends the combination of:
Evaluation of parameters such as time, temperature and pressure, through indicators and records available on the equipment.
Indicators that respond to process conditions and help check whether the sterilizing agent has reached the inside of the packaging.
Use of indicators containing highly resistant microorganisms, such as spores of Geobacillus stearothermophilus, to directly evaluate the effectiveness of the sterilization process (CDC, 2024).
Monitoring is not distrusting the autoclave. It is objectively checking whether the process is working as it should.
This is even demonstrated by studies carried out in dental offices.
In a study with 230 sterilizers from 200 dental offices, 39 pieces of equipment showed a positive result in biological monitoring. Among the causes identified were errors related to time, temperature or pressure, lack of supervision of the procedure and inadequate maintenance (MORALES et al., 2015).
Another classic study, which evaluated sterilizers in dental offices, also identified operator errors as an important cause of sterilization failures, reinforcing that the equipment and the execution of the process need to be considered together (HASTREITER et al., 1991).
In other words:
A good autoclave operated incorrectly remains a vulnerable process.
There is a tendency to think of maintenance as something related to the useful life of the equipment.
But it is also related to process reliability.
RDC nº 15/2012 determines that information on technical interventions be recorded and establishes the need for requalification of equipment after situations such as change of location, malfunction, repairs or suspected failure in the process, including chemical and biological indicators when applicable (ANVISA, 2012).
This creates an important logic:
equipment → maintenance → monitoring → traceability.
They are not independent steps.
The process is not over yet.
The packaging must be intact and dry before storage.
Damp, torn, or punctured packages should be considered compromised and need to be reprocessed before use (CDC, 2024).
Therefore, we can think of sterilization as a chain:
clean → prepare → pack → sterilize → monitor → store → check before use.
If a step is neglected, process safety can be compromised.
Both.
An adequate autoclave is a fundamental part of the system.
But sterilization does not happen simply because we press “start”.
It depends on the quality of the equipment + preparation of the instruments + correct loading + cycle parameters + monitoring + maintenance + storage.
So perhaps the best way to think of it is:
The autoclave runs the cycle. The process ensures that this cycle results in a safe instrument for the next patient.
And this difference is enormous.
Because investing in good equipment is important.
Knowing how to operate, monitor, maintain and document this equipment is what transforms technology into security.
HASTREITER, R. J. et al. Effectiveness of dental office instrument sterilization procedures. Journal of the American Dental Association, vol. 122, no. 10, p. 51-56, 1991.
MORALES, N. et al. Biological monitoring and causes of failure in cycles of sterilization in dental care offices in Mexico. American Journal of Infection Control, 2015.
SAVAGE, N.W.; WALSH, L. J. The use of autoclaves in the dental surgery. Australian Dental Journal, vol. 40, n. 3, p. 197-200, 1995.
VAN DOORNMALEN GOMEZ HOYOS, J. P. C. M. et al. Monitoring steam sterilization processes in the dental office. Nederlands Tijdschrift voor Tandheelkunde, v. 122, no. 4, p. 218-224, 2015.
BRAZIL. National Health Surveillance Agency (ANVISA). RDC Resolution No. 15, of March 15, 2012. Provides for good practice requirements for the processing of health products. Brasília, DF, 2012.
CENTERS FOR DISEASE CONTROL AND PREVENTION (CDC). Best Practices for Sterilization Monitoring in Dental Settings. 2024.
CENTERS FOR DISEASE CONTROL AND PREVENTION (CDC). Sterilization and Disinfection. 2024.
CENTERS FOR DISEASE CONTROL AND PREVENTION (CDC). Steam Sterilization. 2023
Explore outros conteúdos, aprofunde seus conhecimentos e descubra novas possibilidades para sua carreira.